|
Mechanical
|
|
|
Shaft Diameter
|
3/8” nominal
|
|
Shaft Loading
|
Up to 40 pounds axial and 20 pounds radial applied 1/4” from housing
|
|
Shaft Runout
|
0.0005 T.I.R
|
|
Starting Torque at 25°C
|
4.0 in-oz (max)
|
|
Bearings
|
Class ABEC 7 standard
|
|
Shaft Material
|
303 stainless steel
|
|
Enclosure
|
Die cast aluminum, hard anodized with dichromate sealed finish. Shaft seals and sealed bearings are standard to achieve environmental ratings.
|
|
Bearing Life
|
2 X 108revs (1300 hrs at 2500 RPM) at rated load; 1 X 1010 revs (67,000 hrs at 2500 RPM) at10% of rated load
|
|
Maximum RPM
|
10,000 RPM (see frequency response, below)
|
|
Moment of Inertia
|
4.1 X 10–4 oz-in-sec2 UL & MSHA/ 1.7 X 10–3 oz-in-sec2 CEN
|
|
Weight
|
64 oz typical (approx 4 lbs)
|
|
Electrical
|
|
|
Code
|
Incremental
|
|
Output Format
|
2 channels in quadrature, 1/2 cycle index gated with negative B channel
|
|
Cycles per Shaft Turn
|
1 to 72,000 (see table 2, page 5). For resolutions above 3,600 see Note 7.
|
|
Supply Voltage
|
5 to 28 VDC
|
|
Current Requirements
|
100 mA typical +output load, 250 mA (max)
|
|
Voltage/Output
|
(see note 3)
15V/V: Line Driver, 5–15 VDC in, Vout = Vin
28V/V: Line Driver, 5–28 VDC in, Vout = Vin
28V/5: Line Driver, 5–28 VDC in, Vout = 5 VDC
28V/OC: Open Collector, 5–28 VDC in, Ocout
|
|
Protection Level
|
Reverse, overvoltage and output short circuit (see note 3)
|
|
Frequency Response
|
100 KHz Typical, Higher frequency response available, see note 5
|
|
Output Terminations
|
see Table 1, page 5
|
|
Termination Type
|
Compression type, UL recognized. Accepts AWG 14 to 22, stranded wire, strip 1/4”
|
|
Note
|
Consult factory for other electrical options
|
|
Environmental
|
|
|
Enclosure Rating
|
NEMA 4 X & 6 (IP66), outdoor Non-Hazardous locations, NEMA 4 X & 13 (IP66), indoor NonHazardous locations
|
|
Temperature
|
Standard operating all models, 0° to +70°C; Storage all models, -50° to +90°C; Extended temp testing avail.: for UL, -40° to +80°C; for CEN, -50° to +90°C
|
|
Shock
|
50 g’s at 11 msec
|
|
Vibration
|
5 to 2000 Hz @ 20 g’s
|
|
Humidity
|
100% RH
|
|
Hazardous Area Rating
|
UL listed for use in hazardous locations. Class I, Group D, or Class I, Groups C & D, and Class II,Groups E, F & G. NEMA Enclosure 7.
|